Ultra guard is a two component (acrylic/cementitious) flexible waterproof protective coating for marble/stone, concrete and masonry substrate. Ultra Guard is a elastromeric ready to use two part system, which waterproof/weatherproofs and protects concrete and similar structures. Specially formulated for wide range of applications:- Swimming pools, retaining walls, pile heads, submerged tunnels, stones/marbles, bridge deck, bathrooms, permanent wet areas and wide variety of extreme service class structures.
Cemguard PC 400 can be applied to new or old concrete structures that are structurally sound:
It is essential that good concreting practice is performed and maintained at every stage of the application process. Ensure that Ultra guard is cured properly after application. Minimum 3 days curing is essential before flooding.
Matshepo Africa will be pleased to offer full technical support on specific applications.
Ultra guard is a two-part system supplied as a preblended powder mix and a new generation of environmentally friendly acrylic emulsion specifically designed to modify cement composition.
Ulta guard is alkaline and should not come into contact with skin or eyes. Avoid inhalation of ust during mixing. Gloves, goggles and dust masks should be worn. Splashes to eyes should be washed immediately with water & seek medical advice.
The information supplied in our literature or given by our employees is based upon extensive experience and together with that supplied by our agents or distrbutors, is given in good faith in order to help you. Our company policy is one of the continuous Research and development, we therefore reserve the right to update this information at any time without prior notice. We also guarantee the consistent high quality of our products; however, as we have no control over site conditions or the execution of the work, we accept no liability for liability for any loss or damage which may arise as a result thereof.
| Colour | Grey / White |
|---|---|
| VOC (DCL) | < 1 g/l |
| Toxicity | Non toxic |
| Mix Density | 1.9 Kg/Lit |
| Solid Content ( Polymer ) | 80% |
| Abrasion resistance | 0.09 cm/km |
| Tensile Strength ASTM D751 | >0.5 N/mm2 |
| Elongation ASTM D 412 98a | >50% |
| Crack bridging | >0.5 mm |
| Chloride content/td> | < 0.1% |
| Water penetration (7 Bar) Resistance to positive | Nil |
| Water pressure (DIN 1048) Resistance to negative | Nil |
| Water Pressure (DIN 1048) | 3 Bar |
| Chloride Ion diffusivity | |
| 90 Days | Zero penetration |
| Yield 27 Kg Kit | Approx 18.9 Ltrs |
Based on test carried out at standard conditions of temperature and %relative humidity
Approximately 13.5 m2 / 27 kg Kit @ 1 mm thickness.
DIN 1048, part 5: 1991, EN 14891, BS 8102, ASTM C836.
Apply the first coat at an average 800 – 1000 micron and fill all the poros completely. Second coat should apply ( approx. 1mm) only after the completecuring (min 48 hours) of the first coat. We recommend that, the treated area should be protected against direct sunlight and damp cured by covering with damp hessian or similar. But not compulsory. Do not flood or over expose to water until it is completely cured.
Virgin polypropylene mesh can be used over joints, cracks and whole reinforcement application. When the completion of the first coat installs the mesh tightly and overcoat the entire area.
Surface should be cleaned and remove all loose particles prior to Ultra Guard applications. Wet the surface prior to the application. Surrounding the pipes & fittings must be treated with Ultra Guard EP system. Corners/ Edges should be carefully treated with fibre mesh reinforcement.
Two coat of Ultra Guard applied @1kg/m2 first coat by a masonry brush or appropriate power spray equipment. All applications where two coats are recommended, the second coat shall be applied when the first coat is completely dried. Do not flood or over expose to water until it is completely cured. Total build up thickness > 1mm DFT. Recommended to apply two coats @ 1mm thick at a coverage of approximately 1kg/m2.
Recommended to apply one coat @ 1 mm thick at a coverage of approximately 0.7 – 1kg/m2.
ULTRA GUARD shelf-life period of 12 months, if stored in a cool and dry environment.
| Available Packing | ||||
|---|---|---|---|---|
| 12 Kg Kit | 15 Kg Kit | 20 Kg Kit | 27 Kg Kit | |
| Powder | 8 Kg | 15 Kg Kit | 20 Kg Kit | 27 Kg Kit |
| Liquid | 4kg | 5kg | 5kg | 7kg |
| Minimum Coating Thickness | |
|---|---|
| Swimming Pools | 2mm |
| Wet Area Floor | 2mm |
| Water tanks | 2mm |
| Marble / Stones | 1mm |
ULTRA GUARD
Manufactured and Packed in Kenya By,
Matshepo Africa LTD Athi 55 Business Park , Godown : 53, Mlolongo, Athi River, Nairobi, Kenya P.O Box No – 2873 - 00606
Ph : 0757775555
Email : simba@matshepo.com
www.simbagrip.com